Maker Feather S3 IoT Kit - Simplifying IoT with V-ONE, for Industry and STEM learning

⭐️⭐️⭐️ Maker Feather S3 IoT Kit - Simplifying IoT with V-ONE ⭐️⭐️⭐️  

⭐️ Following the new feature release by ViTrox, Cyton Technologies grab this opportunity to collaborate and use their IoT platform, V-ONE. With the new features AIoT module in V-ONE, it can be one of the best IoT platforms that you should try! Never heard of this V-ONE platform? Don't worry, this IoT Kit is included with an online manual guide that will help you explore the V-ONE with various IoT projects for you to try!
 
❗️Note: V-ONE platform is initially built for industrial use, so the user interface is quite different from other IoT platforms. A lot of work and improvements have been made to make this platform more user-friendly. So, students out there, come and give it a try!
 
⭐️ AIoT Cloud is a platform where any user, from an engineer to a student, can use an AIoT device or AIoT gateway to connect with a readymade V-ONE AIoT Cloud data storage structure for real-time monitoring, analytics, and adoption of AI and Machine Learning in V-ONE.


 
⭐️ This IoT Kit is powered by a powerful microcontroller; Cyron Maker Feather AIoT S3. With the onboard ESP32-S3 module, it will not be a problem to run various IoT projects using different types of sensors and actuators.



⭐️ This online manual guide will cover everything you need to know, including the V-ONE platform, Arduino IDE software, and the guide to run each sample project.



⭐️ For some preview, this is the final dashboard for one of the sample projects, Smart Agriculture. Unleash your creativity and create your own dashboard!



⭐️⭐️⭐️ Features ⭐️⭐️⭐️ 
	📌 A special collaboration with ViTrox to utilize their great IoT platform, V-ONE.
	📌 Use a powerful microcontroller board, Cytron Maker Feather AIoT S3 which is capable to run various IoT projects.
	📌 Beginner-friendly, no more complicated wiring with the presence of Maker ports.
	📌 Step-by-step online manual guide to explore the V-ONE platform.
	📌 Complete tutorial for all the sample projects.
		5 sample projects for Basic Kit
		10 sample projects for Complete Kit
	📌 Suitable for makers, electronics enthusiasts, and students (tertiary and secondary education).
 
⭐️⭐️⭐️ Maker Feather AIoT S3 Specifications ⭐️⭐️⭐️ 
	📌 Adafruit Feather form factor
	📌 Powered by ESP32-S3
	📌 Single-cell LiPo connector with overcharge / over-discharge protection circuit, rechargeable via USB.
	📌 11 x Status indicator LEDs for GPIOs
	📌 1 x Programmable piezo buzzer (Connected to GPIO12)
	📌 1 x Reset button
	📌 1 x User programmable button (GPIO3)
	📌 1 x RGB LEDs
	📌 3x Maker Ports, compatible with Qwiic, STEMMA QT, and Grove (via conversion cable)
	📌 Support Arduino, CircuitPython, MicroPython & Espressif IDF
	📌 Dimension: 58.42mm x 22.86mm

⭐️⭐️⭐️  Packing list ⭐️⭐️⭐️ 

	📦 Complete Kit
		1 x Maker Feather AIoT S3 (Presoldered Headers)
		1 x USB C Cable
		1 x Breadboard
		1 x DHT11 Sensor
		1 x PIR Sensor
		1 x Rain / Water Level Sensor
		1 x MQ2 Smoke Sensor
		1 x Moisture Sensor Module
		2 x Infrared Sensor Module
		1 x 1CH Active H/L 3V OctoCoupler Relay Module
		1 x SG90 Micro Servo
		1 x 300C 1.5-6VDC 7mm Shaft Motor
		1 x DIY 4 Blades 56mm Motor Propeller (Blue)
		2 x Push Button
		LED
			1 x Red
			1 x Green
			1 x Yellow
		3 x Resistor 0.25W 5% 220Ohm
		3 x Qwiic Cable
		20 x Male to Male Jumper Wire (20cm)
		1 x Philips Head Screwdriver
		Registration Card for FREE V-ONE Account
 
	📦 Basic Kit
		1 x Maker Feather AIoT S3 (Presoldered Header)
		1 x USB C Cable
		1 x Breadboard
		1 x Rain / Water Level Sensor
		1 x Moisture Sensor Module
		2 x Infrared Sensor Module
		1 x SG90 Micro Servo
		2 x Push Button
		3 x Qwiic Cable
		10 x Male to Male Jumper Wire (20cm)
		Registration Card for FREE V-ONE Account

	📦 Add-on Sensors for Basic Kit
		1 x DHT11 Sensor
		1 x PIR Sensor
		1 x MQ2 Smoke Sensor
		1 x 1CH Active H/L 3V OctoCoupler Relay Module
		1 x 300C 1.5-6VDC 7mm Shaft Motor
		1 x DIY 4 Blades 56mm Motor Propeller (Blue)
		LED
			1 x Red
			1 x Green
			1 x Yellow
		3 x Resistor 0.25W 5% 220Ohm
		10 x Male to Male Jumper Wire (20cm)
		1 x Philips Head Screwdriver


📩 Email us at [email protected] for technical support 😊
☎️ Call us at 04-548 0668
🚚 Free shipping WITHOUT min. purchase for students & teachers (ONLY applicable on website purchase) 🤩
💻 Visit us at my.cytron.io for more product choices 😊